Skip to main content
BluINFO

Mercury Commands and Codes

  1. Last updated
  2. Save as PDF

Overview

This article will help understand the various error codes that Mercury Hardware may generate.

 

When using the Realtime Control these are the command code that show up in the "Replies From Controller" Window.

Ex. Feb 23 07:22:34 Controller: (10,1):434 DOOR SENSOR-6, 9:3 Door: 00 (was 00), AccPt: 01 (was 00)

In the example the Mercury code is 9.3, the portal is secure.

1:x:

Transaction TypeSysComm: Reports System Status (1:x):
1.1 SCP power-up diagnostics
1.2 host communications off-line
1.3 host communications on-line
1.4 Transaction count exceeds the preset limit

2:x:

TypeSioComm: Reports on SIO communication status when the communication is established or there is a change in communication status (2:x)
2.1 communication disabled (result of host command)
2,2 off-line: timeout (no/bad response from unit)
2.3 off-line: invalid identification from SIO 
2.4 off-line: command too long
2.5 on-line: normal connection
2.6 hexLoad report: ser_num is address loaded (-1 = last record)

3:x:

TypeCardBin: Reports binary card data when a card is read (3:x)
3.1   Access Denied, Invalid Card Format

4:x:

TypeCardBcd: Reports card data when a card is read (4:x)
4.1 Access Denied, Invalid Card Format, forward read
4.12 Access Denied, Invalid Card Format, reverse read

5:x:

TypeCardFull: Reports formatted card: 32-bit card number length: (5:x)
5.1 Request rejected: access point "locked"
5.2 Request accepted: access point "unlocked"
5.3 Request rejected: invalid facility code
5.4 Request rejected: invalid facility code extension
5.5 Request rejected: not in card file
5.6 Request rejected: invalid issue code
5.7 Request granted: facility code verified, not used
5.8 Request granted: facility code verified, door used
5.,9 Access denied - asked for host approval, then timed out
5.10 Reporting that this card is "about to get access granted" (expecting C_329 Host Response)
5.11 Access denied count exceeded
5.12 Access denied - asked for host approval, then host denied

6:x:

TypeCardID: Reports formatted card: 32-bit card number length: (6:x)
  6.1 Request rejected: de-activated card
6.2 Request rejected: before activation date
6.3 Request rejected: after expiration date
6.4 Request rejected: invalid time
6.5 Request rejected: invalid PIN
6.6 Request rejected: anti-passback violation
6.7 Request granted: APB violation, not used
6.8 Request granted: APB violation, used
6.9 Request rejected: duress code detected
6.10 Request granted: duress, used
6.11 Request granted: duress, not used
6.12 Request granted: full test, not used
6.13 Request granted: full test, used
6.14 Request denied: never allowed at this reader (all Tz's = 0)
6.15 Request denied: no second card presented
6.16 Request denied: occupancy limit reached
6.17 Request denied: the area is NOT enabled
6.18 Request denied: use limit
6.19 Request denied: unauthorized assets
6.20 Request denied: biometric verification error
6.21 Granting access: used/not used transaction will follow
6.22 Request rejected: failed the bio test: no bio record
6.23 Request rejected: failed the bio test: no bio device
6.24 Request rejected: no escort card presented
6.25 Reserved
6.26 Reserved
6.27 Reserved
6.28 Request rejected: no asset present – asset is required
 

7:x:

TypeCoS: Reports Change-of-state status (7:x)
7.1 Disconnected (from an input point ID)
7.2 Unknown (off-line): no report from the ID
7.3 Secure (or de-activate relay)
7.4 Alarm (or activated relay: perm or temp)
7.5 Fault
7.6 Exit delay in progress
7.7 Entry delay in progress

8:x:

TypeREX: Reports Exit request when the REX has been used (8:x)
8.1 Exit cycle: door use not verified
8.2 Exit cycle: door not used
8.3 Exit cycle: door used
8.4 Host initiated request: door use not verified
8.5 Host initiated request: door not used
8.6 Host initiated request: door used

9:x:

TypeCoSDoor: Reports Door Status Monitor Change-Of-State (9:x)
9.1 Disconnected.
9.2 Unknown _RS bits: last known status.
9.3 Secure.
9.4 Alarm (forced, held open or both).
9.5 Fault (Fault type is encoded in door_status byte).

10:x:

TypeProcedure: Reports Procedure log (10:x)
10.1 Cancel procedure (abort delay), see Command 312, Procedure Control Command.
10.2 Execute procedure (start new), see Command 312, Procedure Control Command.
10.3 Resume procedure, if paused; see Command 312, Procedure Control Command.
10.4 Execute procedure with prefix 256 actions; see Command 312, Procedure Control Command.
10.5 Execute procedure with prefix 512 actions; see Command 312, Procedure Control Command.
10.6 Execute procedure with prefix 1024 actions; see Command 312, Procedure Control Command.
10.7 Resume procedure with prefix 256 actions; see Command 312, Procedure Control Command.
10.8 Resume procedure with prefix 512 actions; see Command 312, Procedure Control Command.
10.9 Resume procedure with prefix 1024 actions; see Command 312, Procedure Control Command.
10.10 Command was issued to procedure with no actions – (NOP)

11:x:

TypeUserCmnd: Reports User Command Request report (11:x)
11.1 Command entered by the user.

12:x:

TypeActivate: Reports change of state: for trigger variable or time zone (12:x)
12.1 Became inactive.
12.2 Became active.

13:x:

TypeAcr: Reports ACR mode changes (13:x)
13.1 Disabled.
13.2 Unlocked
13.3 Locked (exit request enabled)
13.4 Facility code only
13.5 Card only
13.6 PIN only
13.7 Card and PIN
13.8 PIN or card

14:x:

TypeMPG: Reports Monitor Point Group status (14:x)
 14.1 First disarm command executed (mask_count was 0, all MPs got masked)
14.2 Subsequent disarm command executed (mask_count incremented, MPs already masked)
14.3 Override command: armed (mask_count cleared, all points unmasked)
14.4 Override command: disarmed (mask_count set, unmasked all points)
14.5 Force arm command, MPG armed, (may have active zones, mask_count is now zero)
14.6 Force arm command, MPG not armed (mask_count decremented)
14.7 Standard arm command, MPG armed (did not have active zones, mask_count is now zero)
14.8 Standard arm command, MPG did not arm, (had active zones, mask_count unchanged)
14.9 Standard arm command, MPG still armed, (mask_count decremented)
14.10 Override arm command, MPG armed (mask_count is now zero)
14.11 Override arm command, MPG did not arm, (mask_count decremented)

15:x:

TypeArea: Reports Access Area (15:x)
15.1 area disabled
15.2 area enabled
15.3 occupancy count reached zero
15.4 occupancy count reached the "downward-limit"
15.5 occupancy count reached the "upward-limit"
15.6 occupancy count reached the "max-occupancy-limit"
15.7 multi-occupancy mode changed

16:x:

TypeAsset: Reports Asset Transaction: 52-bit (double) card number length: (16:x)
16.1 Asset: no access request, no card
16.2 Asset: no temp buffer to queue asset
16.3 Asset: timeout, no card event
16.4 Asset: have card, asset not in database
16.5 Asset: have card, card is owner
16.6 Asset: have card, card has class rights
16.7 Asset: have card, card has no rights
16.8 Asset: sent a TamperSet command

17:x:

TypeBio1: Reports Biometric Data: 52bit (double) card number length: (17:x)
17.1 Verify/enroll operation failed, no card data available, no template data available
17.2 Verify/enroll operation completed, no card data available, have template data
17.3 Verify operation failed, have card data, no template data available
17.4 Verify operation completed, did not pass, have card data, have template data
17.5 Verify operation completed, passed, have card data, have template data
17.6 Enroll operation complete

18:x:

TypeUserCmndX: Reports Extended User Command (18:x)
18.1 Executed the command.
18.2 Rejected user command: command is not allowed at this ACR.
18.3 Rejected user command: not authorized at this ACR.
18.4 Rejected user command: invalid command parameter(s).

19:x:

TypeUseLimit: Reports Use Limit update (19:x)
19.1 Use limit changed, reporting new limit

21:x:

TypeDblCardFull: Reports formatted card: 52-bit (double) card number length: (21:x)
21.1 Request rejected: access point "locked"
21.2 Request accepted: access point "unlocked"
21.3 Request rejected: invalid facility code
21.4 Request rejected: invalid facility code extension
21.5 Request rejected: not in card file
21.6 Request rejected: invalid issue code
21.7 Request granted: facility code verified, not used
21.8 Request granted: facility code verified, door used
21.9 Access denied - asked for host approval, then timed out
21.10 Reporting that this card is "about to get access granted" (expecting C_329 Host Response)
21.11 Access denied count exceeded
21.12 Access denied - asked for host approval, then host denied

22:x:

TypeDBLCardID: Reports formatted card: 52-bit (double) card number length: (22:x)
22.1 Request rejected: de-activated card
22.2 Request rejected: before activation date
22.3 Request rejected: after expiration date
22.4 Request rejected: invalid time
22.5 Request rejected: invalid PIN
22.6 Request rejected: anti-passback violation
22.7 Request granted: APB violation, not used
22.8 Request granted: APB violation, used
22.9 Request rejected: duress code detected
22.10 Request granted: duress, used
22.11 Request granted: duress, not used
22.12 Request granted: full test, not used
22.13 Request granted: full test, used
22.14 Request denied: never allowed at this reader (all Tz's = 0)
22.15 Request denied: no second card presented
22.16 Request denied: occupancy limit reached
22.17 Request denied: the area is NOT enabled
22.18 Request denied: use limit
22.19 Request denied: unauthorized assets
22.20 Request denied: biometric verification error
22.21 Granting access: used/not used transaction will follow
22.22 Request rejected: failed the bio test: no bio record
22.23 Request rejected: failed the bio test: no bio device
22.24 Request rejected: no escort card presented
22.25 Reserved
22.26 Reserved
22.27 Reserved
22.28 Request rejected: no asset present – asset is required
 

23:x:

TypeMpgIps: Reports IPS Group State Changes (23:x)
23.1 DISARMED, all points normal (no zones in fault/trouble state)
23.2 DISARMED, some points in fault state (supervisory fault or point)
23.3 ARMED_AWAY,
23.4 ARMED_STAY,
23.5 ARMED_INSTANT
23.6 ARMED, entry delay is in progress
23.7 ARMING, exit delay is in progress
23.8 NEW_ALARM
23.9 ALARM_CANCELED
23.10 PointSet
23.11 Disarmed, but some points active

32:x:

TypeAssetI64: Reports Asset Transaction: 64-bit (Int64) card number length: (32:x)
32.1 Asset: no access request, no card
32.2 Asset: no temp buffer to queue asset
32.3 Asset: timeout, no card event
32.4 Asset: have card, asset not in database
32.5 Asset: have card, card is owner
32.6 Asset: have card, card has class rights
32.7 Asset: have card, card has no rights
32.8 Asset: sent a TamperSet command

33:x:

TypeBio1I64: Reports Biometric Data: 64bit (Int64) card number length: (33:x)
33.1 Verify/enroll operation failed, no card data available, no template data available
33.2 Verify/enroll operation completed, no card data available, have template data
33.3 Verify operation failed, have card data, no template data available
33.4 Verify operation completed, did not pass, have card data, have template data
33.5 Verify operation completed, passed, have card data, have template data
33.6 Enroll operation complete

37:x:

TypeI64CardFull: Reports formatted card: 64-bit (I64) card number length: (37:x)
37.1 Request rejected: access point "locked"
37.2 Request accepted: access point "unlocked"
37.3 Request rejected: invalid facility code
37.4 Request rejected: invalid facility code extension
37.5 Request rejected: not in card file
37.6 Request rejected: invalid issue code
37.7 Request granted: facility code verified, not used
37.8 Request granted: facility code verified, door used
37.9 Access denied - asked for host approval, then timed out
13.10 Reporting that this card is "about to get access granted" (expecting C_329 Host Response)
37.11 Access denied count exceeded
37.12 Access denied - asked for host approval, then host denied

38:x:

TypeI64CardID: Reports formatted card: 64-bit (I64) card number length: (38:x)
38.1 Request rejected: de-activated card
38.2 Request rejected: before activation date
38.3 Request rejected: after expiration date
38.4 Request rejected: invalid time
38.5 Request rejected: invalid PIN
38.6 Request rejected: anti-passback violation
38.7 Request granted: APB violation, not used
38.8 Request granted: APB violation, used
38.9 Request rejected: duress code detected
38.10 Request granted: duress, used
38.11 Request granted: duress, not used
38.12 Request granted: full test, not used
38.13 Request granted: full test, used
38.14 Request denied: never allowed at this reader (all Tz's = 0)
38.15 Request denied: no second card presented
38.16 Request denied: occupancy limit reached
38.17 Request denied: the area is NOT enabled
38.18 Request denied: use limit
38.19 Request denied: unauthorized assets
38.20 Request denied: biometric verification error
38.21 Granting access: used/not used transaction will follow
38.22 Request rejected: failed the bio test: no bio record
38.23 Request rejected: failed the bio test: no bio device
38.24 Request rejected: no escort card presented
38.25 Reserved
38.26 Reserved
38.27 Reserved
38.28 Request rejected: no asset present – asset is required
 

53:x:

TypeI64CardFullIc32: Reports formatted card: 64-bit (I64) card number length with 32-bit issue code: (53:x)
53.1 Request rejected: access point "locked"
53.2 Request accepted: access point "unlocked"
53.3 Request rejected: invalid facility code
53.4 Request rejected: invalid facility code extension
53.5 Request rejected: not in card file
53.6 Request rejected: invalid issue code
53.7 Request granted: facility code verified, not used
53.8 Request granted: facility code verified, door used
53.9 Access denied - asked for host approval, then timed out
53.10 Reporting that this card is "about to get access granted" (expecting C_329 Host Response)
53.11 Access denied count exceeded
53.12 Access denied - asked for host approval, then host denied

65:x:

TypeAcrExtFeatureCoS:  Reports ACR Extended Feature Change of State events 
65.3 Secure / Inactive
65.4 Alarm / Active
  1. Back to top
  • Was this article helpful?

Recommended articles

  1. Article type
    Topic
    Stage
    Review
  2. Tags
    1. Codes
    2. Commands
    3. Hardware
    4. Mercury
    5. Realtime Controller
    6. Status Codes