AI 2 Reader – Remote (AIR 2)
READER INTERFACE MODULE WITH POE+
(2 DOORS, 4 READERS, 6 INPUTS, 4 OUTPUTS)
The new HID Mercury MR Series 3 Serial Input/Output modules enable system expansion of HID Mercury intelligent controllers as part of HID’s distributed architecture. The enhanced modules offer an improved processor and increased memory, plus feature an embedded crypto memory chip that provides a secured layer of encryption to onboard sensitive data. Built on the HID Mercury open platform, Series 3 modules provide the necessary flexibility for OEMs, channel partners and end customers to choose the controller configuration that best fits their needs.
The MR62e Series 3 is an IP-enabled interface module with on-board flexibility to connect a wide range of security devices. The MR62e is easy to install and provides the required I/O for interfacing four card readers using OSDP protocol, six general-purpose input monitor points and four control relays to any HID Mercury intelligent controller.
The MR62e provides increased power output using PoE+ and provides one reader port supporting OSDP Secure Channel readers, including non-keypad, keypad and biometric readers. System configuration and setup are provided through HID Mercury OEM partner software applications. The MR62e Series 3 is the latest generation door interface module for HID Mercury intelligent controllers, the platform of choice for customers seeking open architecture access control solutions.
- IP-to-the-Door
- Edge-capable input/output module supporting PoE+ power
- Provides up to 1.5 A of power at door for reader, lock and more
- Security and Network
- IPv4/v6
- Intelligent Controller to MR62e communication protected by AES
- MR62e web browser communication protected by TLS
- Zerconf Device Discovery (mDNS)
- Card Reader Functions
- OSDP Reader Only
- Anti-passback support (area, reader and time based)
- Programmable keypad user commands
- Open Architecture - High performance, reliable platform enables use of hardware with HID Mercury OEM partners’ software solutions.
- IP-to-the-Door - Supports PoE+ power, removing the cost of traditional power supplies and home-run wiring.
- Enhanced Security - Embedded crypto memory chip and data at rest encryption provides secured layer of protection of sensitive data.
- OSDP Protocol - Secure channel communications for reader connectivity.
- Versatile Interoperability - Same reliable interface and identical footprint as the EP Controllers, enabling seamless upgrades for existing deployments.
System Diagram
Specifications
| Access Control |
|
| Door Control |
|
General |
| Primary Power | 12 to 24 VDC ± 10 %, 500 mA maximum (reader and USB ports not included) |
| Reader Port | 600 mA maximum (add 600 mA to primary power current) |
| Micro USB Port | 5 VDC, 500 mA maximum (add 270 mA to primary power current) |
| Battery | Memory/Clock Backup: 3 Volt Lithium, type BR2330 or CR2330 |
| microSD Card | microSD or microSDHC; 2GB to 8GB |
| Host Communication | Ethernet: 10-BaseT/100Base-TX and USB port (2.0) with optional adapter: pluggable model USB2-OTGE100 |
| Serial I/O Device | 2-wire RS-485, 2,400 to 115,200 bps, asynchronous, half-duplex, 1 start bit, 8 data bits, and 1 stop bit |
| Inputs | Eight unsupervised/supervised, standard EOL: 1k/1k ohm, 1%, ¼ watt. Two unsupervised dedicated for cabinet tamper and UPS fault monitoring |
| Output Relays | Four relays, Form C, NO 5 A @ 30 VDC resistive, NC 3 A @ 30 VDC resistive |
Reader Interface |
| Reader Power | 12-24 VDC ± 10 % regulated, 300 mA maximum each reader |
| Data Inputs | TTL compatible, F/2F or 2-wire RS-485 |
| RS-485 Mode | 9,600 to 115,200 bps, asynchronous, half-duplex, 1 start bit, 8 data bits, and 1 stop bit. Maximum cable length: 2000 ft. (609.6 m) |
| LED Output | TTL levels, high>3 V, low<0.5 V, 5 mA source/sink maximum |
| Buzzer Output | Open collector, 12 VDC open circuit maximum, 40 mA sink maximum |
Cable Requirements |
| Power and Relays | 1 twisted pair, 18 to 16 AWG |
| Ethernet | CAT-5, minimum |
| Reader TTL | 6-conductor, 18 AWG, 500 feet (150 m) maximum |
| Reader F/2F | 4-conductor, 18 AWG, 500 feet (150 m) maximum |
| Reader RS-485 | 1 twisted pair, shielded, 120 ohm impedance, 24 AWG, 2,000 ft. (610 m) max. |
| I/O Devices | 1 twisted pair with drain wire and shield, 120 ohm impedance, 24 AWG, 4,000 ft. (1,219 m) maximum |
| Alarm Input | 1 twisted pair, 30 ohms maximum |
Environmental |
| Temperature | -55 to +85 °C, storage, 0 to +70 °C, operating |
| Humidity | 5 to 95% RHNC |
Mechanical |
| Dimensions | 8 in. (203.2 mm) W x 6 in. (152.4 mm) L x 1 in. (25 mm) H |
| Weight | 9 oz. (255 g) nominal, board only |
Compliance and Warranty |
| Product Compliance | UL 294 Recognized, FCC Part 15 Class A, CE Compliant, RoHS (2011/65/EU & 2015/863), EU REACH (1907/2006), California Proposition 65, NIST Certified Encryption |
| Warranty | The product is warranted free from defects in material and workmanship under normal use and service with proper maintenance for one year from the date of factory shipment. |
Ordering Information:
| MFG Part # | BluBØX Order # | Description |
|---|---|---|
| XXXX | XXXX | XXXX |
| XXXX | XXXX | XXXX |